Honda

Honda Genuine 90181-S7A-000 Flange Bolt (14x77)

Honda Genuine 90181-S7A-000 Flange Bolt (14x77)

$11.49

✔ Honda Genuine 90181-S7A-000 Flange Bolt (14x77) — OEM Rear Suspension Strut Mounting Bolt for CR-V, Element & Civic
✔ Compatibility: Select 2002–2006 Honda CR-V and Element, plus 2006–2008 Civic Hybrid models — verify by VIN before ordering
✔ Direct replacement for the factory rear strut flange bolt — secures the lower shock absorber mounting point
✔ Genuine Honda OEM part — not an aftermarket reproduction
✔ M14x1.5 thread, 77mm length under head, 17mm hex, Grade 10.9 steel with zinc coating
✔ Often required in pairs — verify quantity needed for your application
✔ Compact and sturdy — approximately 0.13–0.24 lb (60–110 g) per bolt depending on source

 

Honda Genuine 90181-S7A-000 Flange Bolt — Rear Suspension Strut Mounting Bolt for Honda Models

Suspension bolts are easy to overlook until one is seized, stripped, or missing. The genuine Honda 90181-S7A-000 flange bolt is the factory-correct fastener for the rear lower strut mounting position on several Honda models. Whether you are replacing a corroded bolt during a suspension refresh or completing a strut replacement, using the OEM fastener ensures proper thread engagement, correct grade, and the clamping force the suspension design requires.

This is a genuine Honda flange bolt (part number 90181-S7A-000), commonly listed as a rear suspension strut bolt. It features an M14x1.5 thread with a 77mm length below the head and a 17mm hex head . The bolt is Grade 10.9 steel with a zinc-coated finish for corrosion resistance . It is positioned at the rear left or right lower suspension mounting point on the applications listed below . Some sources indicate a required quantity of 2 per vehicle .

When to Replace

• Bolt is seized, corroded, or rounded from previous service
• Bolt is missing or was damaged during strut removal
• Suspension refresh or strut replacement is being performed
• Visible thread damage or stretching on the existing bolt
• Factory service procedure specifies replacement of torque-to-yield or damaged fasteners

Product Details & Highlights

• ✔ Genuine Honda OEM part — factory-correct thread, grade, and finish
• ✔ M14x1.5 thread with 77mm shank — matches the original suspension fastener specification
• ✔ Grade 10.9 steel construction — rated for suspension clamping loads
• ✔ Zinc-coated finish — resists corrosion in exposed underbody conditions
• ✔ 17mm hex head — standard tool compatibility
• ✔ Direct replacement — installs at the factory rear strut mounting location

Package Contents

• 1 × Honda Genuine 90181-S7A-000 Flange Bolt (14x77)

FAQ

FAQ

Is this a genuine Honda part or an aftermarket reproduction?
This is a genuine Honda OEM part (90181-S7A-000). It is the factory-specified fastener, not an aftermarket substitute.

Will this fit my 2005 Honda CR-V?
The 2005 CR-V is listed as compatible for rear suspension strut mounting . Confirm by VIN or contact the seller with your vehicle details before ordering.

How many bolts do I need?
Some parts catalogs indicate a required quantity of 2 per vehicle for the rear strut application . Inspect your vehicle and confirm the scope of your repair before ordering.

What are the bolt specifications?
M14x1.5 thread, 77mm length under head, 33mm thread length, 17mm hex head, Grade 10.9 steel, zinc-coated .

Is this the front or rear strut bolt?
Factory parts diagrams position this bolt at the rear left or right suspension mounting point .

Can I reuse the old bolt?
If the original bolt is undamaged, clean, and threads freely, reuse may be possible. However, suspension fasteners exposed to corrosion and load cycles are often replaced as a precaution during strut service. Inspect carefully before deciding.

California Proposition 65

WARNING

Cancer and Reproductive Harm.

www.p65warnings.ca.gov

View full details